- 相關推薦
2024年數控機床維修常見機床報警中英文對照大全
為幫助大家了解更多數控機床維修的相關知識，下面，小編為大家分享數控機床維修常見機床報警中英文對照大全，希望對大家有所幫助!
超程報警 Over Travel Alarm
急停報警 Emergency Stop Alarm
伺服系統故障報警 Servo System Fault Alarm
主軸故障報警 Spindle Fault Alarm
刀具故障報警 Tool Fault Alarm
潤滑系統故障報警 Lubrication System Fault Alarm
冷卻系統故障報警 Cooling System Fault Alarm
氣壓不足報警 Insufficient Air Pressure Alarm
電機過載報警 Motor Overload Alarm
編碼器故障報警 Encoder Fault Alarm
通信故障報警 Communication Fault Alarm
內存不足報警 Insufficient Memory Alarm
電池電量低報警 Low Battery Power Alarm
系統過熱報警 System Overheat Alarm
軸鎖定報警 Axis Lock Alarm
位置偏差過大報警 Excessive Position Deviation Alarm
速度異常報警 Abnormal Speed Alarm
行程開關故障報警 Limit Switch Fault Alarm
驅動器故障報警 Drive Fault Alarm
機床未就緒 Machine Not Ready
刀具磨損報警 Tool Wear Alarm
液壓系統故障 Hydraulic System Fault
絲桿故障報警 Lead Screw Fault Alarm
導軌故障報警 Guideway Fault Alarm
換刀故障報警 Tool Change Fault Alarm
夾緊裝置故障 Clamping Device Fault
加工精度超差報警 Machining Accuracy Out of Tolerance Alarm
電源故障報警 Power Supply Fault Alarm
溫度過高報警 Excessive Temperature Alarm
壓力異常報警 Abnormal Pressure Alarm
機械部件干涉報警 Mechanical Component Interference Alarm
傳感器故障報警 Sensor Fault Alarm
控制系統故障 Control System Fault
電機過熱報警 Motor Overheat Alarm
編碼器信號丟失報警 Encoder Signal Loss Alarm
操作錯誤報警 Operating Error Alarm
回零故障報警 Home Position Return Fault Alarm
軟限位報警 Soft Limit Alarm
硬限位報警 Hard Limit Alarm
程序錯誤報警 Program Error Alarm
數據丟失報警 Data Loss Alarm
風扇故障報警 Fan Fault Alarm
濾波故障報警 Filter Fault Alarm
接口故障報警 Interface Fault Alarm
看門狗故障報警 Watchdog Fault Alarm
螺距誤差報警 Pitch Error Alarm
反向間隙過大報警 Backlash Excessive Alarm
振動過大報警 Excessive Vibration Alarm
噪聲異常報警 Abnormal Noise Alarm
防護門未關閉報警 Protective Door Not Closed Alarm
自動潤滑故障報警 Automatic Lubrication Fault Alarm
排屑故障報警 Chip Removal Fault Alarm
對刀錯誤報警 Tool Setting Error Alarm
坐標系錯誤報警 Coordinate System Error Alarm
卡盤故障報警 Chuck Fault Alarm
尾座故障報警 Tailstock Fault Alarm
光柵尺故障報警 Grating Scale Fault Alarm
T 碼錯誤 tworderror
油位低 lowoillevel
主軸故障 spinplefault
主軸報警 spindlealarm
急停按鈕被按下 externalemgstop
交流盤未準備好 acnotready
主軸潤滑故障 spinplelubefault
T 代碼出錯，非法 T 代碼 tcodeerror
M 代碼出錯，非法 M 代碼 mcodeerror
伺服未準備好 servonotready
NC 沒準備好 ncnotready
轉塔故障 turretfault
轉塔限位 turretlimit
直流 24V 斷開 dc24vopen
+24V 沒準備好 +24vnotready
檔位漂移 grardrift
【數控機床維修常見機床報警中英文對照】相關文章：
數控機床的維修技巧02-27
如何維修數控機床-維修診斷數控機床的八種方法02-26
數控機床維修的基本功03-21
數控機床與傳統機床的區別03-27
維修數控機床的六種方法12-21
數控機床故障分析與維修經驗總結03-24